4164/41256 RAM Modification: Difference between revisions
More actions
No edit summary |
|||
| (14 intermediate revisions by the same user not shown) | |||
| Line 13: | Line 13: | ||
That triple-rail requirement made the 4116 a weak link on these boards, especially as the linear supplies aged and the rails got noisy. | That triple-rail requirement made the 4116 a weak link on these boards, especially as the linear supplies aged and the rails got noisy. | ||
== 4164 | == 4164 First Successor == | ||
In the early 1980s the direct successor appeared: the '''4164''' (65,536 × 1-bit). | In the early 1980s the direct successor appeared: the '''4164''' (65,536 × 1-bit). | ||
An internal bias generator supplies the −5 V, so the part runs from a '''single +5 V''' rail. Pins that used to carry the extra supplies became another address bit, which is how capacity went up. 4164s generally run cooler and tolerate supply variation better. | An internal bias generator supplies the −5 V, so the part runs from a '''single +5 V''' rail. Pins that used to carry the extra supplies became another address bit, which is how capacity went up. 4164s generally run cooler and tolerate supply variation better. | ||
== 41256 == | == 41256 Last 16-Pin Successor == | ||
By the late 1980s density had increased again. Using the last unused supply pin as another address line gave the '''41256''' (262,144 × 1-bit). | By the late 1980s density had increased again. Using the last unused supply pin as another address line gave the '''41256''' (262,144 × 1-bit). | ||
== Pinout | == Pinout Comparison == | ||
Here is a comparison in pinout: | Here is a comparison in pinout: | ||
[[File:Ram_Comparison.png|center|800px|4116 vs 4164 vs 41256 pinout]] | [[File:Ram_Comparison.png|center|800px|4116 vs 4164 vs 41256 pinout]] | ||
== Modify the MPU == | |||
What we need to do: For the 4164/41256 to work, we need to accomplish a few things. | |||
* '''Remove the -5v from Pin 1''' | |||
* '''Remove the +12v from Pin 8''' | |||
* '''Substitute +5v on Pins 1 and 8 (If we left these unconnected/floating, the address value would randomly change''' | |||
* '''The goal is to have +5 on Pins: 1,8 and 9. Ground stays on Pin 16 | |||
Original MPU Power Connector Pinout | |||
[[File:MPU_Unmod_Power_-_Noted.png|center|800px|Original MPU Power Connector Pinout]] | |||
'''Step 1''' — Cut pins 5(+12 Regulated) and 9(-5v) * Keep one of the cut off pins * | |||
* Note - The 'Polarizing Key is on Pin 4. With the mod, if the connector is reversed/flipped it can't be plugged in * | |||
* Note - Pin 1 is on the right and Pin 9 is on the left * | |||
[[File:Modified_Power_Connector.jpg|center|800px|Pins 5 and 9 cut]] | |||
== See also == | == See also == | ||
* [[Hardware - General]] | * [[Hardware - General]] | ||
* [[Battery Damage]] | * [[Battery Damage]] | ||
Latest revision as of 04:50, 12 September 2026
Williams MPUs shipped with 24 × Mostek 4116 DRAM (16,384 × 1-bit), introduced in 1977 — only a few years before Defender.
These chips need three voltages (triple-rail):
- +5 V — TTL input/output buffers
- +12 V — primary power
- −5 V — substrate bias / shield
If −5 V drops while +5 and +12 are still present, the chip overheats and fails quickly.
That triple-rail requirement made the 4116 a weak link on these boards, especially as the linear supplies aged and the rails got noisy.
4164 First Successor
In the early 1980s the direct successor appeared: the 4164 (65,536 × 1-bit).
An internal bias generator supplies the −5 V, so the part runs from a single +5 V rail. Pins that used to carry the extra supplies became another address bit, which is how capacity went up. 4164s generally run cooler and tolerate supply variation better.
41256 Last 16-Pin Successor
By the late 1980s density had increased again. Using the last unused supply pin as another address line gave the 41256 (262,144 × 1-bit).
Pinout Comparison
Here is a comparison in pinout:
Modify the MPU
What we need to do: For the 4164/41256 to work, we need to accomplish a few things.
- Remove the -5v from Pin 1
- Remove the +12v from Pin 8
- Substitute +5v on Pins 1 and 8 (If we left these unconnected/floating, the address value would randomly change
- The goal is to have +5 on Pins: 1,8 and 9. Ground stays on Pin 16
Original MPU Power Connector Pinout
Step 1 — Cut pins 5(+12 Regulated) and 9(-5v) * Keep one of the cut off pins *
- Note - The 'Polarizing Key is on Pin 4. With the mod, if the connector is reversed/flipped it can't be plugged in *
- Note - Pin 1 is on the right and Pin 9 is on the left *
